Your basket is empty.

Added to Basket

MAC Flight Stands (4) Large 60mm

$12.95 $11.66

Specification
Product Code standlarge60
Condition
Weight 0.07000Kg

This product is always in stock.

One set of four (4) laser cut acrylic magnetic flight stands for table top wargaming. Cut from 3mm acrylic, with two heights included (2 x 45mm and 2 x 33mm overall). All parts (except magnets) come to you with a protective paper coating so as not to be scratched during transit to you.

Tired of having your flight stands snap from your flyer/skimmer models? Or do you leave your stands unglued so they can be packed separately for transport, only to have your models tip and spin during game play when sitting on the peg? Well look no further, with Magnetic Flight Stands you get the best of both worlds. Models are held firmly in place during gameplay, but can be separated from their stands for transport. What you get:

  • 4 x 60mm Round Bases
  • 2 x 45mm Pegs
  • 2 x 30mm Pegs
  • 4 x Large Support Arms
  • 4 x Small Support Arms
  • 8 x 3mm x 3mm x 3mm Square RE Magnets
  • 8 x 3mm x 2mm Disc RE Magnets

Using a combination laser cut acrylic and rare earth magnets (N50), and tested on a wide range of small, medium and large flyer and skimmer kits for 25mm to 30mm gaming, following these simple steps for assembly will see to it that you never have to use another type of flight stand again.

NOTE: Best used on medium and large plastic flyers/skimmers, that are usually deployed in squadrons of upto 3 or individually. Especially so if there is added weight at one point, such as the rear, due to turrets and/or sponsons

These instructions are for the Large Stands only. For the Small Stands please see the appropriate listing as they are different for assembly purposes.

STEP 1: Starting with your components, 1 Base, 1 Peg, 2 Round 3mm (diameter) x 2mm (thickness) Magnets, 2 Square 3mm Magnets and either the large or small support arm (depending on the kit you are using it for).

Remove your protective paper coating from both the base, peg and support arm.

STEP 2: Some people find it ideal to super glue the peg into the stand at this stage, as it gives something more to hold onto while placing magnets.

Already being a snug fit, you may need to give a little down ward pressure onto a flat surface for the peg to make definate contact with the base at the join. Using super glue will simply make sure that it never falls out.

STEP 3: Before placing and gluing any magnets, you will need to make sure of polarity. Simply take one square and one round magnet and let them join together. Do this for 2 pairs (and keep them a good distance away from each other so you dont get your polarities mixed up). This is how the magnets will sit while your model is joined to the stand.

STEP 4: Start by test fitting your square magnet into one of the two small square slots at the top of the peg (as pictured). The top surface of the square magnet will sit flush with the top of the peg, leaving the round magnet sitting proud.

Remove the magnets and apply super glue to the three surfaces you noticed that come in contact with the peg. Keep the super glue as minimal as possible, so as to minimise mess. The magnet is a snug fit also.

Allow to dry.

STEP 4a: Again, test fit your second square magnet into the other small square slots at the top of the peg (as pictured). The top surface of the square magnet will sit flush with the top of the peg, leaving the round magnet sitting proud.

Remove the magnets and apply super glue to the three surfaces you noticed that come in contact with the peg. Keep the super glue as minimal as possible, so as to minimise mess. The magnet is a snug fit also.

Set this aside and allow to dry.

STEP 5: Moving onto your model to be mounted on the stand, locate where your normal flight stand peg would go.

STEP 6: Drill the hole out to a diameter of 3mm. The best way to do this while putting minimal stress on small plastic components is to run a 3mm drill bit in a cordless drill on a backwards setting. This actually turns the excess plastic into powder under a more controlled action, rather than removing large amounts of swarf too quickly and undesirably.

Drill to a minimum of 2mm deep to allow full insertion of the round magnet, any less and you wont get it to sit flush with the models surface.

STEP 6a: Using your flight stand peg as a marker (with magnets attached), locate where you want the second magnet hole to be drilled. On larger kits with more weight in one location, it is better to have the second magnet closer to that area. For example, if your skimmer/flyer has a rear turret (thus extra weight at the rear) place the second magnet hole towards the rear, when compared to the original.

STEP 7: It is recommended to use a pin vice with a 1mm drill bit to get this started. The 1mm hole will act as a pilot hole for your 3mm drill bit.

 

STEP 8: Drill the hole out to a diameter of 3mm. The best way to do this while putting minimal stress on small plastic components is to run a 3mm drill bit in a cordless drill on a backwards setting. This actually turns the excess plastic into powder under a more controlled action, rather than removing large amounts of swarf too quickly and undesirably.

Drill to a minimum of 2mm deep to allow full insertion of the round magnet, any less and you wont get it to sit flush with the models surface.

STEP 9: Place a minimal amount of super glue in each hole you have drilled out. With the round magnets still attached to the peg as shown here (so as to keep your polarity correct) push the round magnets into the holes.

STEP 10: The peg and square magnets wont allow you to push the round magnets any further than flush with the models surface. So even if you have drilled more than 2mm, it simply isnt a problem.

STEP 11: All that is left is for you to choose which support arm to place in the center slot. Two sizes are supplied per stand, giving you the best possible outcomes, depending on the kit your are assembling.

Simply slide either arm onto the center slot, preferably adding a minimal amount of super glue to keep it in place. Support arms are also a snug fit onto the peg.

These arms have been designed to simply add left and right OR forward and backward support (depending on your magnet location). The two magnets will do all of the grabbing work, the arm will just stop any tip when the model is moved.

Once dry you have now fully assembled your Magnetic Acrylic Flight Stand. You can now place your model ontop and see how it clicks into position.

While most modellers/gamers prefer clear stands, you also have the option of having your stands made in any of our available colours. Check the colour swatches below for examples.&

Opaque Black
Opaque Black
Opaque White
Opaque White
Opaque Red
Opaque Red
Opaque Blue
Opaque Blue
Opaque Yellow
Opaque Yellow
Opaque Orange
Opaque Orange
Opaque Green
Opaque Green
Transparent Light Grey
Transparent Light Grey
Transparent Dark Grey
Transparent Dark Grey
Transparent Red
Transparent Red
Transparent Blue
Transparent Blue
Transparent Green
Transparent Green
Transparent Yellow
Transparent Yellow
Clear
Clear